Wednesday, March 11, 2009

OXYGEN

From : Wikipedia.org


Industrial production

Two major methods are employed to produce 100 million tonnes of O2 extracted from air for industrial uses annually. The most common method is to fractionally-distill liquefied air into its various components, with nitrogen N2 distilling as a vapor while oxygen O2 is left as a liquid.

Hoffman electrolysis apparatus used in electrolysis of water.
The other major method of producing O2 gas involves passing a stream of clean, dry air through one bed of a pair of identical zeolite molecular sieves, which absorbs the nitrogen and delivers a gas stream that is 90% to 93% O2. Simultaneously, nitrogen gas is released from the other nitrogen-saturated zeolite bed, by reducing the chamber operating pressure and diverting part of the oxygen gas from the producer bed through it, in the reverse direction of flow. After a set cycle time the operation of the two beds is interchanged, thereby allowing for a continuous supply of gaseous oxygen to be pumped through a pipeline. This is known as pressure swing adsorption. Oxygen gas is increasingly obtained by these non-cryogenic technologies (see also the related vacuum swing adsorption).

Oxygen gas can also be produced through electrolysis of water into molecular oxygen and hydrogen. DC electricity must be used: if AC is used, the gases in each limb consist of hydrogen and oxygen in the explosive ratio 2:1. Contrary to popular belief, the 2:1 ratio observed in the DC electrolysis of acidified water does not prove that the empirical formula of water is H2O unless certain assumptions are made about the molecular formulae of hydrogen and oxygen themselves.

A similar method is the electrocatalytic O2 evolution from oxides and oxoacids. Chemical catalysts can be used as well, such as in chemical oxygen generators or oxygen candles that are used as part of the life-support equipment on submarines, and are still part of standard equipment on commercial airliners in case of depressurization emergencies. Another air separation technology involves forcing air to dissolve through ceramic membranes based on zirconium dioxide by either high pressure or an electric current, to produce nearly pure O2 gas.

In large quantities, the price of liquid oxygen in 2001 was approximately $0.21/kg. Since the primary cost of production is the energy cost of liquefying the air, the production cost will change as energy cost varies.

For reasons of economy, oxygen is often transported in bulk as a liquid in specially-insulated tankers, since one litre of liquefied oxygen is equivalent to 840 liters of gaseous oxygen at atmospheric pressure and 20 °C. Such tankers are used to refill bulk liquid oxygen storage containers, which stand outside hospitals and other institutions with a need for large volumes of pure oxygen gas. Liquid oxygen is passed through heat exchangers, which convert the cryogenic liquid into gas before it enters the building. Oxygen is also stored and shipped in smaller cylinders containing the compressed gas; a form that is useful in certain portable medical applications and oxy-fuel welding and cutting.




Applications


Medical
An oxygen concentrator in an emphysema patient's house
Uptake of O2 from the air is the essential purpose of respiration, so oxygen supplementation is used in medicine. Oxygen therapy is used to treat emphysema, pneumonia, some heart disorders, and any disease that impairs the body's ability to take up and use gaseous oxygen. Treatments are flexible enough to be used in hospitals, the patient's home, or increasingly by portable devices. Oxygen tents were once commonly used in oxygen supplementation, but have since been replaced mostly by the use of oxygen masks or nasal cannulas.

Hyperbaric (high-pressure) medicine uses special oxygen chambers to increase the partial pressure of O2 around the patient and, when needed, the medical staff. Carbon monoxide poisoning, gas gangrene, and decompression sickness (the 'bends') are sometimes treated using these devices. Increased O2 concentration in the lungs helps to displace carbon monoxide from the heme group of hemoglobin. Oxygen gas is poisonous to the anaerobic bacteria that cause gas gangrene, so increasing its partial pressure helps kill them. Decompression sickness occurs in divers who decompress too quickly after a dive, resulting in bubbles of inert gas, mostly nitrogen and helium, forming in their blood. Increasing the pressure of O2 as soon as possible is part of the treatment.

Oxygen is also used medically for patients who require mechanical ventilation, often at concentrations above 21% found in ambient air.


Life support and recreational use

Low pressure pure O2 is used in space suitsA notable application of O2 as a low-pressure breathing gas is in modern space suits, which surround their occupant's body with pressurized air. These devices use nearly pure oxygen at about one third normal pressure, resulting in a normal blood partial pressure of O2. This trade-off of higher oxygen concentration for lower pressure is needed to maintain flexible spacesuits.

Scuba divers and submariners also rely on artificially-delivered O2, but most often use normal pressure, and/or mixtures of oxygen and air. Pure or nearly pure O2 use in diving at higher-than-sea-level pressures is usually limited to rebreather, decompression, or emergency treatment use at relatively shallow depths (~ 6 meters depth, or less). Deeper diving requires significant dilution of O2 with other gases, such as nitrogen or helium, to help prevent oxygen toxicity.

People who climb mountains or fly in non-pressurized fixed-wing aircraft sometimes have supplemental O2 supplies. Passengers traveling in (pressurized) commercial airplanes have an emergency supply of O2 automatically supplied to them in case of cabin depressurization. Sudden cabin pressure loss activates chemical oxygen generators above each seat, causing oxygen masks to drop and forcing iron filings into the sodium chlorate inside the canister. A steady stream of oxygen gas is produced by the exothermic reaction. However, even this may pose a danger if inappropriately triggered: a ValuJet airplane crashed after use-date-expired O2 canisters, which were being shipped in the cargo hold, activated and caused fire. The canisters were mis-labeled as empty, and carried against dangerous goods regulations.

Oxygen, as a supposed mild euphoric, has a history of recreational use in oxygen bars and in sports. Oxygen bars are establishments, found in Japan, California, and Las Vegas, Nevada since the late 1990s that offer higher than normal O2 exposure for a fee. Professional athletes, especially in American football, also sometimes go off field between plays to wear oxygen masks in order to get a supposed "boost" in performance. However, the reality of a pharmacological effect is doubtful; a placebo or psychological boost being the most plausible explanation. Available studies support a performance boost from enriched O2 mixtures only if they are breathed during actual aerobic exercise. Other recreational uses include pyrotechnic applications, such as George Goble's five-second ignition of barbecue grills.


Industrial
Most commercially-produced O2 is used to smelt iron into steel.
Smelting of iron ore into steel consumes 55% of commercially-produced oxygen. In this process, O2 is injected through a high-pressure lance into molten iron, which removes sulfur impurities and excess carbon as the respective oxides, SO2 and CO2. The reactions are exothermic, so the temperature increases to 1700 °C.

Another 25% of commercially-produced oxygen is used by the chemical industry. Ethylene is reacted with O2 to create ethylene oxide, which, in turn, is converted into ethylene glycol; the primary feeder material used to manufacture a host of products, including antifreeze and polyester polymers (the precursors of many plastics and fabrics).

Most of the remaining 20% of commercially-produced oxygen is used in medical applications, metal cutting and welding, as an oxidizer in rocket fuel, and in water treatment. Oxygen is used in oxyacetylene welding burning acetylene with O2 to produce a very hot flame. In this process, metal up to 60 cm thick is first heated with a small oxy-acetylene flame and then quickly cut by a large stream of O2. Rocket propulsion requires a fuel and an oxidizer. Larger rockets use liquid oxygen as their oxidizer, which is mixed and ignited with the fuel for propulsion.


Scientific

500 million years of climate change vs

Paleoclimatologists measure the ratio of oxygen-18 and oxygen-16 in the shells and skeletons of marine organisms to determine what the climate was like millions of years ago (see oxygen isotope ratio cycle). Seawater molecules that contain the lighter isotope, oxygen-16, evaporate at a slightly faster rate than water molecules containing the 12% heavier oxygen-18; this disparity increases at lower temperatures. During periods of lower global temperatures, snow and rain from that evaporated water tends to be higher in oxygen-16, and the seawater left behind tends to be higher in oxygen-18. Marine organisms then incorporate more oxygen-18 into their skeletons and shells than they would in a warmer climate. Paleoclimatologists also directly measure this ratio in the water molecules of ice core samples that are up to several hundreds of thousands of years old.

Planetary geologists have measured different abundances of oxygen isotopes in samples from the Earth, the Moon, Mars, and meteorites, but were long unable to obtain reference values for the isotope ratios in the Sun, believed to be the same as those of the primordial solar nebula. However, analysis of a silicon wafer exposed to the solar wind in space and returned by the crashed Genesis spacecraft has shown that the Sun has a higher proportion of oxygen-16 than does the Earth. The measurement implies that an unknown process depleted oxygen-16 from the Sun's disk of protoplanetary material prior to the coalescence of dust grains that formed the Earth.

Oxygen presents two spectrophotometric absorption bands peaking at the wavelengths 687 and 760 nm. Some remote sensing scientists have proposed using the measurement of the radiance coming from vegetation canopies in those bands to characterize plant health status from a satellite platform. This approach exploits the fact that in those bands it is possible to discriminate the vegetation's reflectance from its fluorescence, which is much weaker. The measurement is technically difficult owing to the low signal-to-noise ratio and the physical structure of vegetation; but it has been proposed as a possible method of monitoring the carbon cycle from satellites on a global scale.




Compounds

Water (H2O) is the most familiar oxygen compound.
The oxidation state of oxygen is −2 in almost all known compounds of oxygen. The oxidation state −1 is found in a few compounds such as peroxides.[88] Compounds containing oxygen in other oxidation states are very uncommon: −1/2 (superoxides), −1/3 (ozonides), 0 (elemental, hypofluorous acid), +1/2 (dioxygenyl), +1 (dioxygen difluoride), and +2 (oxygen difluoride).

Oxides and other inorganic compounds

Water (H2O) is the oxide of hydrogen and the most familiar oxygen compound. Hydrogen atoms are covalently bonded to oxygen in a water molecule but also have an additional attraction (about 23.3 kJ·mol−1 per hydrogen atom) to an adjacent oxygen atom in a separate molecule. These hydrogen bonds between water molecules hold them approximately 15% closer than what would be expected in a simple liquid with just Van der Waals forces.

formulaDue to its electronegativity, oxygen forms chemical bonds with almost all other elements at elevated temperatures to give corresponding oxides. However, some elements readily form oxides at standard conditions for temperature and pressure; the rusting of iron is an example. The surface of metals like aluminium and titanium are oxidized in the presence of air and become coated with a thin film of oxide that passivates the metal and slows further corrosion. Some of the transition metal oxides are found in nature as non-stoichiometric compounds, with a slightly less metal than the chemical formula would show. For example, the natural occurring FeO (wüstite) is actually written as Fe1−xO, where x is usually around 0.05.

Oxygen as a compound is present in the atmosphere in trace quantities in the form of carbon dioxide (CO2). The earth's crustal rock is composed in large part of oxides of silicon (silica SiO2, found in granite and sand), aluminium (aluminium oxide Al2O3, in bauxite and corundum), iron (iron(III) oxide Fe2O3, in hematite and rust) and other metals.

The rest of the Earth's crust is also made of oxygen compounds, in particular calcium carbonate (in limestone) and silicates (in feldspars). Water-soluble silicates in the form of Na4SiO4, Na2SiO3, and Na2Si2O5 are used as detergents and adhesives.

Oxygen also acts as a ligand for transition metals, forming metal–O2 bonds with the iridium atom in Vaska's complex, with the platinum in PtF6, and with the iron center of the heme group of hemoglobin.



Organic compounds and biomolecules

Organic compounds and biomoleculesAmong the most important classes of organic compounds that contain oxygen are (where "R" is an organic group): alcohols (R-OH); ethers (R-O-R); ketones (R-CO-R); aldehydes (R-CO-H); carboxylic acids (R-COOH); esters (R-COO-R); acid anhydrides (R-CO-O-CO-R); and amides (R-C(O)-NR2). There are many important organic solvents that contain oxygen, including: acetone, methanol, ethanol, isopropanol, furan, THF, diethyl ether, dioxane, ethyl acetate, DMF, DMSO, acetic acid, and formic acid. Acetone ((CH3)2CO) and phenol (C6H5OH) are used as feeder materials in the synthesis of many different substances. Other important organic compounds that contain oxygen are: glycerol, formaldehyde, glutaraldehyde, citric acid, acetic anhydride, and acetamide. Epoxides are ethers in which the oxygen atom is part of a ring of three atoms.

Oxygen reacts spontaneously with many organic compounds at or below room temperature in a process called autoxidation. Most of the organic compounds that contain oxygen are not made by direct action of O2. Organic compounds important in industry and commerce that are made by direct oxidation of a precursor include ethylene oxide and peracetic acid.
The element is found in almost all biomolecules that are important to (or generated by) life. Only a few common complex biomolecules, such as squalene and the carotenes, contain no oxygen. Of the organic compounds with biological relevance, carbohydrates contain thO2e largest proportion by mass of oxygen. All fats, fatty acids, amino acids, and proteins contain oxygen (due to the presence of carbonyl groups in these acids and their ester residues). Oxygen also occurs in phosphate (PO43−) groups in the biologically important energy-carrying molecules ATP and ADP, in the backbone and the purines (except adenine) and pyrimidines of RNA and DNA, and in bones as calcium phosphate and hydroxylapatite.




Precautions


Toxicity

Oxygen gas (O2) can be toxic at elevated partial pressures, leading to toxicityconvulsions and other health problems. Oxygen toxicity usually begins to occur at partial pressures more than 50 kilopascals (kPa), or 2.5 times the normal sea-level O2 partial pressure of about 21 kPa. Therefore, air supplied through oxygen masks in medical applications is typically composed of 30% O2 by volume (about 30 kPa at standard pressure). At one time, premature babies were placed in incubators containing O2-rich air, but this practice was discontinued after some babies were blinded by it.

Breathing pure O2 in space applications, such as in some modern space suits, or in early spacecraft such as Apollo, causes no damage due to the low total pressures used. In the case of spacesuits, the O2 partial pressure in the breathing gas is, in general, about 30 kPa (1.4 times normal), and the resulting O2 partial pressure in the astronaut's arterial blood is only marginally more than normal sea-level O2 partial pressure (see arterial blood gas).

Oxygen toxicity to the lungs and central nervous system can also occur in deep scuba diving and surface supplied diving. Prolonged breathing of an air mixture with an O2 partial pressure more than 60 kPa can eventually lead to permanent pulmonary fibrosis. Exposure to a O2 partial pressures greater than 160 kPa may lead to convulsions (normally fatal for divers). Acute oxygen toxicity can occur by breathing an air mixture with 21% O2 at 66 m or more of depth while the same thing can occur by breathing 100% O2 at only 6 m.



Combustion and other hazards

Highly-concentrated sources of oxygen promote rapid combustion. Fire and explosion hazards exist when concentrated oxidants and fuels are brought into close proximity; however, an ignition event, such as heat or a spark, is needed to trigger combustion. Oxygen itself is not the fuel, but the oxidant. Combustion hazards also apply to compounds of oxygen with a high oxidative potential, such as peroxides, chlorates, nitrates, perchlorates, and dichromates because they can donate oxygen to a fire.
Pure O2 at higher than normal pressure and a spark led to a fire and the loss of the Apollo 1 crew.

Concentrated O2 will allow combustion to proceed rapidly and energetically. Steel pipes and storage vessels used to store and transmit both gaseous and liquid oxygen will act as a fuel; and therefore the design and manufacture of O2 systems requires special training to ensure that ignition sources are minimized. The fire that killed the Apollo 1 crew on a test launch pad spread so rapidly because the capsule was pressurized with pure O2 butCombustion and other hazards at slightly more than atmospheric pressure, instead of the ⅓ normal pressure that would be used in a mission.

Liquid oxygen spills, if allowed to soak into organic matter, such as wood, petrochemicals, and asphalt can cause these materials to detonate unpredictably on subsequent mechanical impact.[105] As with other cryogenic liquids, on contact with the human body it can cause burns to the skin and the eyes.


Source : http://en.wikipedia.org/wiki/Oxygen